Zanussi Refrigerator ZA 96 3 W User Manual

REFRIGERATOR-  
FREEZER  
ZA 96/3 W  
INSTRUCTION BOOKLET  
2222 177-66  
 
CONTENTS  
Instructions for the User  
Instructions for the  
Installer  
2
4
Important Safety Information  
13  
14  
Technical Specification  
Operation  
Before use  
4
4
4
4
4
4
4
5
5
5
5
5
6
6
6
Installation  
Positioning  
Control panel  
14  
14  
Starting your appliance  
Setting the temperature  
Ambient Temperature Switch  
The freezer compartment  
Freezing fresh food  
Frozen food storage  
Thawing  
Shelf holders  
15  
16  
Electrical Connection  
Rear Spacers  
16  
Door Reversal  
Making ice cubes  
Cold accumulators  
Fresh food refrigeration  
Movable shelves  
Positioning the door shelves  
Freezing calendar  
7
8
Hints and Tips  
Maintenance and Cleaning  
Internal cleaning  
8
8
8
8
9
External cleaning  
When the appliance is not in use  
Changing the light bulb  
Defrosting  
10  
11  
11  
12  
Something Not Working  
Service and Spare Parts  
Customer Care  
Guarantee Conditions  
3
 
OPERATION  
Before using  
Remove all securing tapes. Wash inside the  
appliance with lukewarm water and bicarbonate of  
soda (5 ml to 0.5 litre of water).  
Do not use soap or detergent as the smell may  
linger. Dry thoroughly.  
Control panel  
AB C  
D
A. Pilot light for ambient temperature switch  
B. Ambient temperature switch  
C. Operating pilot light  
D. Thermostat control knob  
Starting your appliance  
Insert the plug into the wall socket.  
The operating pilot light (C) will illuminate.  
Setting the temperature  
If you wish to return to a lower temperature, turn the  
thermostat to a higher number, however you should  
turn the setting lower occasionally to allow automatic  
defrosting.  
Ambient Temperature Switch  
The temperature inside the refrigerator is regulated  
by a thermostat with different temperature positions  
and an “OFF” (O) position.  
Low Ambient Temperature Switch  
To ensure that the appliance is working efficiently  
when the room temperature drops below 16°C, the  
switch mounted on the control panel should be  
pressed.  
Position = minimum coldness  
G
Position G = maximum coldness  
Insert a coin to turn the thermostat dial to the  
required position.  
No damage can be caused by leaving the switch in  
this position for any period of time (see page 10 Low  
ambient operation). However should the temperature  
rise above 16°C remember to press again the switch.  
The thermostat setting can vary as the temperature  
inside the refrigeration compartment depends on the  
following factors:  
The freezer compartment  
– room temperature  
– how often the door is opened  
– how much food is stored  
– position of the appliance  
The four-star freezer compartment is suitable for  
storage of commercially frozen food and for freezing  
fresh foods.  
Freezing fresh food  
Important  
When freezing large amounts of fresh food turn the  
thermostat to maximum approximately 1 hour prior to  
freezing. When the food is frozen return the  
thermostat back to the normal position.  
If the fridge is not defrosting correctly, it is possible  
that because a very low temperature has been  
selected, the motor is working continuously, which  
prevents the defrost cycle from operating.  
To ensure correct defrosting, a lower number should  
be selected on the thermostat and you should notice  
that the motor cuts out from time to time, which is  
correct.  
4
 
In any 24 hours you can freeze up to 9 kg. of fresh  
food.  
placement of aluminium wrapping or containers in  
the oven.  
Place food to be frozen in the upper drawer of the  
freezer as this is the coldest part.  
Defrosted cooked food must never be refrozen.  
Frozen food storage  
Making ice cubes  
When first starting-up or after a period of non use,  
before putting the food in the compartment let the  
appliance run for at least two hours on the coldest  
setting, then turn the thermostat knob to the normal  
operating position.  
The appliance is provided with one or more trays for  
ice-cubes trays.  
Fill the tray(s) 3/4 full to give the ice space to expand  
and place them in the freezer compartment.  
To release the ice cubes simply give the tray a slight  
twist.  
Do not exceed the storage period indicated by the  
food manufacturer.  
Do not use sharp or metallic instruments to remove  
the trays from the freezer.  
Finally, do not open the door frequently or leave it  
open longer than is absolutely necessary.  
Cold accumulators  
Important  
The freezer contains two cold accumulators. Place  
the cold accumulators in the FAST FREEZE  
compartment. The cold accumulators increase  
storage times in the event of a power cut or  
breakdown.  
Do not put carbonated liquids, (fizzy drinks etc.), in  
the freezer compartment.  
Ice Iollies, if consumed immediately after removal  
from the freezer, can cause low temperature skin  
burns.  
Removal of these units wll increase the capacity of  
the fast freezing compartment but will reduce  
storage times in the event of a power cut or  
breakdown.  
Do not remove items from the freezer if your hands  
are damp/wet, as this could cause skin abrasions or  
“frost/freezer burns”.  
Fresh food refrigeration  
Important  
To obtain the best performance, do not store warm  
food or evaporating liquids in the refrigerator; do  
cover or wrap the food, particularly if it has a strong  
flavour.  
In the event of a power cut do not open the door. The  
food in the freezer will not be affected if the power  
cut is short and if the freezer is full. Should the food  
begin to thaw, it must be consumed quickly and must  
not be re-frozen. (See “Hits and Tips”)  
Do not cover the shelves with any protective  
material, such as paper, cardboard or plastic, which  
may obstruct the air circulation through them.  
Thawing  
To help you use your refrigerator correctly, here are  
some more useful hints:  
Frozen food, prior to being used, can be thawed in  
the fridge or at room temperature depending on the  
time available. Small food items may even be cooked  
from frozen; in this case cooking will take longer.  
Raw meat (beef, pork, lamb & Poultry): wrap in  
polythene bags and place on the glass shelf on the  
top of the salad crispers.  
Any frozen food which is allowed to thaw accidentally  
should either be eaten as soon as possible or thrown  
away. Alternatively, if the food is uncooked and has  
not been completely defrosted it can be cooked and  
then refrozen.  
Meat can only be stored safely in this way for  
one or two days at the most.  
Fruit & vegetables: these should be thoroughly  
cleaned and placed in the salad crispers.  
Butter & cheese: these should be placed in special  
airtight containers or wrapped in aluminium foil or  
polythene bags to exclude as much air as possible.  
Meat, fish and fruit should be thawed in the  
refrigerator compartment and small pieces of meat  
can even be cooked while still frozen, but you must  
ensure that it is thoroughly cooked through.  
Milk bottles: these should have a cap and should be  
stored in the bottle rack on the door.  
Vegetables should be directly immersed in boiling  
water; ready-cooked dishes can be placed directly in  
the oven in their aluminium wrapping.  
A microwave oven is particularly suitable for thawing  
any type of frozen or deep-frozen food: follow the  
oven instructions, particularly regarding the  
5
 
Movable shelves  
The walls of the refrigerator have runners so that  
shelves can be positioned as desired.  
D338  
Positioning the door shelves  
To permit storage of food packages of various sizes,  
the door shelves can be adjusted in height.  
To do this proceed as shown in the diagram.  
PR260  
Freezing Calendar  
The symbols show different types of frozen goods.  
The numbers indicate storage times in months for the appropriate types of frozen goods.  
6
 
HINTS AND TIPS  
Energy Saving Advice  
Normal Operating Sounds  
You may hear faint gurgling or bubbling sounds  
when the refrigerant is pumped through the coils  
or tubing at the rear, and to the cooling  
plate/evaporator.  
Do not install the appliance close to sources of  
heat, such as a boiler or radiator.  
Locate the appliance in a cool well ventilated  
room and make sure that the air openings of the  
appliance are not obstructed.  
When the compressor is on, the refrigerant is  
being pumped round, and you will hear a whirring  
sound or pulsating noise from the compressor.  
Avoid unnecessary frosting in the cabinet by  
packing all foodstuffs into airtight packages  
before placing them in the freezer.  
A thermostat controls the compressor, and you  
will hear a faint ’click’ when the thermostat cuts in  
and out.  
Always leave warm food to cool down to room  
temperature before placing in the fridge.  
Food Storage  
Food which is to be frozen (when cool) should be  
placed in the fridge before being transferred to  
the freezer.  
To obtain the best performance from your fridge-  
freezer  
Thaw frozen food in the fridge. This will ensure  
safer defrosting of foods and reduce the work of  
the refrigeration unit.  
Do not store warm food or evaporating liquids.  
Avoid buying frozen food if you cannot store it  
straight away. The use of an insulated container is  
advisable. When you arrive home place the frozen  
food in the freezer immediately.  
Try to avoid keeping the door open for long  
periods or opening the door too frequently as  
warm air will enter the cabinet and cause the  
compressor to switch on unnecessarily often.  
Keep the time between buying chilled food and  
placing it in your refrigerator as short as possible.  
Ensure there are no obstructions preventing the  
door from closing properly.  
Do not push food together too much, try to allow  
air to circulate around each item.  
In the Event of a Power Failure  
Do not store food uncovered.  
If there is a power failure during the storage of frozen  
foods, keep the door closed. If the temperature within  
your freezer should rise, do not refreeze the food  
without checking its condition. The following  
guidelines should assist you:  
Ensure that food placed in the freezer is dated  
and labelled and used in date order to ensure  
that food is consumed at its best.  
Remove suspect food from your refrigerator and  
clean, refer to Maintenance and Cleaning.  
Ice-cream: Once thawed should be discarded.  
Lean food keeps better and longer than fatty food,  
salt reduces the storage time.  
Fruits & Vegetables: If soft should be cooked and  
used up.  
Wrap the food in polythene or aluminium freezing  
bags or foil so that they adhere to the food and  
provide an airtight seal .  
Breads & Cakes: Can be refrozen without danger.  
Shellfish: Should be refrigerated and used up  
quickly.  
Packaging which is swollen or has traces of  
refrozen water droplets on the pack could indicate  
that the product has not been kept at a suitable  
temperature and that it may have lost its original  
quality. Partially thawed food must not be  
refrozen, it must be consumed within 24 hours.  
Never exceed the storage times indicated by the  
manufacturer.  
Cooked Dishes: i. e. casseroles should be  
refrigerated and used up.  
Large Pieces of Meat: Can be refrozen providing  
there are still ice crystals remaining within them.  
Small Joints: Should be cooked and can then be  
refrozen as cooked dishes.  
Chicken: Should also be cooked and refrozen as a  
fresh dish.  
7
 
MAINTENANCE AND CLEANING  
Before any maintenance or cleaning work is carried  
out, DISCONNECT the appliance from the  
ELECTRICITY supply.  
Changing the light bulb  
If it becomes necessary to replace the lamp, press on  
the rear hook and at the same time slide the cover in  
the direction indicated by the arrow.  
Internal cleaning  
Clean the inside and accessories with warm water  
and bicarbonate of soda (5ml to 0.5 litre of water).  
Rinse and dry thoroughly.  
NEVER USE DETERGENTS, ABRASIVE  
POWDERS, HIGHLY PERFUMED  
CLEANING PRODUCTS OR WAX  
POLISHES,TO CLEAN THE INTERIOR AS  
THESE WILL DAMAGE THE SURFACE AND  
LEAVE A STRONG ODOUR.  
External cleaning  
Unscrew the bulb and replace it with a new 25 watt  
bulb (available from your nearest Service Force  
Centre).  
Many proprietary kitchen surface cleaners  
contain chemicals that can attack/damage the  
plastics used in this appliance. For this reason it  
is recommended that the outer casing of this  
appliance is only cleaned with warm water with a  
little washing-up liquid added.  
Replace the light cover by sliding it into its original  
position.  
An accumulation of dust will affect the performance  
of the appliance and cause excessive electricity  
consumption.  
You MUST ensure that the appliance is switched  
OFF.  
Once or twice a year dust the condenser (black grill)  
and the compressor at the back of the appliance,  
with a brush or vacuum cleaner, see figure.  
PR259  
When the appliance is not in use  
When the appliance is not in use for long periods,  
disconnect from the electricity supply, empty all  
foods and clean the appliance, leaving the doors ajar  
to prevent unpleasant smells.  
8
 
Defrosting  
Refrigerator  
The refrigerator automatically defrosts every time the  
compressor stops. The water is discharged, via a  
pipe, into a tray located at the back of the appliance  
above the compressor, where it evaporates.  
Important  
To avoid defrost water overflowing into the fridge,  
periodically clean the water discharge hole in the  
centre of the V shaped drip collector at the back of  
the refrigerator compartment behind the salad  
crispers. Use the defrost cleaner provided which you  
will find already inserted into the discharge hole.  
Remember to wash the defrost cleaner in hot soapy  
water at regular intervals. Dry throughly before  
replacing.  
D037  
Freezer  
When the frost has reached a thickness of up to  
4mm it can be removed using the ice scraper  
provided with the appliance. During this operation it  
is not necessary to disconnect the appliance from  
the mains and remove the food. Never use metal  
tools for this operation.  
For complete defrosting (once or twice a year)  
proceed as follows:  
-
turn the thermostat dial to the «OFF» position (O)  
or disconnect the appliance from the mains.  
-
Remove any food from inside the freezer and  
fridge, wrap it in several sheets of newspaper and  
store in a cool,dry place.  
-
Leave the door open and insert the ice scraper  
under the channel in the centre of the lower part  
of the appliance; place a low-sided container  
beneath the scraper to collect the water (see fig.).  
-
-
-
Clean and dry thoroughly.  
Replace the scraper in one of the drawers .  
Reconnect the appliance to the mains or reset  
the thermostat to the normal position.  
-
After letting the appliance run for at least half an  
hour, replace the previously removed food into  
the compartment.  
D068  
Important  
When defrosting the freezer, the fridge is also  
controlled by the thermostat and will not be  
operational during this period. A temperature rise of  
the frozen food packs, during defrosting, may  
shorten their safe storage life.  
9
 
SOMETHING NOT WORKING  
Important: If you call out an engineer to a fault listed below, or to repair a fault caused by incorrect use or  
installation a charge will be made, even if the appliance is under guarantee.  
Before contacting your local Service Force Centre, check the following points:  
Symptom  
Solution  
No power to the appliance  
Check there is power at the socket.  
Check there is not a power cut by checking the  
household lights.  
Check the fuse has not blown.  
The light does not come on  
Ensure that the bulb is correctly fitted.  
Replace the bulb if it has blown.  
Check the door light switch is not jammed.  
The temperature in the fridge or freezer section is  
too high  
Check the thermostat control knob is turned to the  
correct setting relative to ambient conditions.  
Check the ambient temperature is within the  
appliance’s operating limits, please refer to the  
installation section in this instruction book.  
Relocate the appliance if necessary.  
The freezer door will not open  
Has door just been opened? If so leave for a few  
minutes to allow the air pressure to equalise.  
The compressor runs continously  
Adjust the thermostat control knob to give correct  
temperature control. See “Setting the temperature”.  
Check that the doors are closed.  
Large quantities of food have recently been placed in  
the cabinet and/or door is frequently opened.  
Check that air ventilation is not obstructed.  
Excessive frost and ice has built up  
Ensure the doors are not left open.  
Check that nothing is preventing the doors from  
closing.  
Is the door gasket intact and clean.  
Has advised periodic defrosting been carried out.  
Noise  
Refer to normal operating sounds.  
Water under the salad crispers  
Check the drain hole is not blocked. (see  
Maintenance and Cleaning).  
Low ambient operation  
During prolonged periods of low ambient temperatures,ie;10°C and lower, the compressor on single  
compressor fridge freezers can remain inoperative during this time .  
10  
 
This is due to the air temperature within the refrigerator compartment being maintained at 6°C or under thus not  
calling the thermostat to energise the compressor .  
During a normal night time period of approximately 8 hours a traditional fridge freezer can normally maintain the  
frozen food temperature but if the appliance is left for longer period in a low ambient temperature the freezer will  
defrost .  
If, after the above checks, there is still a fault, call your local Service Force Centre.  
In-guarantee customers should ensure that the above checks have been made as the engineer will make a  
charge if the fault is not a mechanical or electrical breakdown.  
Please note that proof of purchase is required for any in-guarantee service calls.  
SERVICE AND SPARE PARTS  
In the event of your appliance requiring service, or if you wish to purchase spare parts, please contact your local  
Service Force Centre by telephoning:-  
0 8 7 0  
5
9 2 9 9 2 9  
Your telephone call will be automatically routed to the Service Force Centre covering your post code area.  
For the address of your local Service Force Centre and further information about Service Force, please visit the  
Before calling out an engineer, please ensure you have read the details under the heading ‘Something Not  
Working?  
When you contact the Service Force Centre you will need to give the following details:  
1.  
2.  
3.  
4.  
5.  
Your name, address and post code  
Your telephone number  
Clear and concise details of the fault  
The model and serial number of the appliance (found on the rating plate)  
The purchase date  
Please note that a valid purchase receipt or guarantee documentation is required for in-guarantee  
service calls.  
CUSTOMER CARE DEPARTMENT  
For general enquiries concerning your Zanussi-Electrolux appliance or for further information on  
Zanussi-Electrolux products, please contact our Customer Care Department by letter or telephone at the  
Customer Care Department  
Zanussi-Electrolux  
55-77 High Street  
Slough  
Berkshire  
SL1 1DZ  
Tel: 08705 727 727 (*)  
* calls to this number may be recorded for training purposes.  
11  
 
GUARANTEE CONDITIONS  
Standard guarantee conditions  
We, Zanussi-Electrolux, undertake that if within 12 months of the date of the purchase this  
ZANUSSI-ELECTROLUX appliance or any part thereof is proved to be defective by reason only of faulty  
workmanship or materials, we will, at our option repair or replace the same FREE OF CHARGE for labour,  
materials or carriage on condition that:  
The appliance has been correctly installed and used only on the electricity supply stated on the rating plate.  
The appliance has been used for normal domestic purposes only, and in accordance with the manufacturer’s  
instructions.  
The appliance has not been serviced, maintained, repaired, taken apart or tampered with by any person not  
authorised by us.  
All service work under this guarantee must be undertaken by a Service Force Centre. Any appliance or  
defective part replaced shall become the Company’s property.  
This guarantee is in addition to your statutory and other legal rights.  
Home visits are made between 8.30am and 5.30pm Monday to Friday. Visits may be available outside these  
hours in which case a premium will be charged.  
Exclusions  
This guarantee does not cover:  
Damage or calls resulting from transportation, improper use or neglect, the replacement of any light bulbs or  
removable parts of glass or plastic.  
Costs incurred for calls to put right an appliance which is improperly installed or calls to appliances outside  
the European Community (EC) or European Free Trade Area.  
Appliances found to be in use within a commercial environment, plus those which are subject to rental  
agreements.  
Products of Zanussi-Electrolux manufacture which are not marketed by Zanussi-Electrolux.  
European Guarantee  
If you should move to another country within Europe then your guarantee moves with you to your new home  
subject to the following qualifications:  
The guarantee starts from the date you first purchased your product.  
The guarantee is for the same period and to the same extent for labour and parts as exists in the new  
country of use for this brand or range of products.  
This guarantee relates to you and cannot be transferred to another user.  
Your new home is within the European Community (EC) or European Free Trade Area.  
The product is installed and used in accordance with our instructions and is only used domestically, i.e. a  
normal household.  
The product is installed taking into account regulations in your new country.  
Before you move please contact your nearest Customer Care centre, listed below, to give them details of your  
new home. They will then ensure that the local Service Organisation is aware of your move and able to look  
after you and your appliances.  
France  
Germany  
Italy  
Senlis  
+33 (0)3 44 62 29 29  
+49 (0)800 234 7378  
+39 (0)0434 39 4700  
+46 (0)8 672 53 90  
+44 (0)1753 219 897  
+353 (0)1 4090751  
Nürnberg  
Pordenone  
Stockholm  
Slough  
Sweden  
UK  
Ireland  
Dublin  
12  
 
TECHNICAL SPECIFICATIONS  
DIMENSIONS  
Height  
165,5  
cm  
Width  
Depth  
60  
cm  
cm  
62,5  
POWER SUPPLY VOLTAGE AND FREQUENCY  
TOTAL POWER ABSORBED  
220-240 V / 50 Hz  
110 W  
AVERAGE DAILY UNITS ELECTRICITY *  
GROSS CAPACITY  
0.64 kWh  
Fridge  
178 l  
86 l  
Freezer  
NET CAPACITY  
Fridge  
176 l  
82 l  
Freezer  
STAR RATING  
* This figure is based on standard test results in accordance with European Standard EN 153.  
Actual consumption will depend on how the appliance is used and where it is located.  
13  
 
INSTALLATION  
Important  
IF YOU ARE DISCARDING AN OLD APPLIANCE  
THAT HAS A LOCK OR CATCH ON THE DOOR,  
YOU MUST ENSURE THAT IT IS MADE  
UNUSABLE TO PREVENT YOUNG CHILDREN  
BEING TRAPPED INSIDE.  
Depending upon the position which you choose for  
your appliance, you may wish to reverse the way in  
which the door opens. To do this, refer to instructions  
on “Door reversal”.  
Important  
Positioning  
This appliance should only be installed at a location  
where the ambient temperature corresponds to the  
climate classification indicated on the rating plate,  
which is located at the left on the inside of the  
appliance.  
It must be possible to disconnect the appliance from  
the mains power supply; the plug must therefore be  
easily accessible after installation.  
The following table shows which ambient  
temperature is correct for each climate classification:  
SN +10°C to + 32°C  
N
+16°C to + 32°C  
ST +18°C to + 38°C  
+18°C to + 43°C  
T
A
B
It should be located in a dry atmosphere, out of  
direct sunlight and away from extreme temperature  
e.g. not next to a boiler or radiator, or in a very cold  
room e.g. an outhouse, where the temperatures may  
fall below 10°C (50°F). If these temperatures are  
exceeded i.e. colder or warmer, then the appliance  
may not operate correctly.  
NP008  
You should also ensure that air can circulate freely  
around the back and the top of the cabinet. There  
must also be at least 100 mm (4”) distance between  
the top of the cabinet and any overhanging kitchen  
furniture (A). Ideally, the appliance should not be  
positioned beneath overhanging furniture (B).  
There should also be a gap of 25 mm either side of  
the appliance. Do not obstruct the space  
underneath. The back of the cabinet may be placed  
close to the wall but must not touch it. DO NOT  
install in places with restricted ventilation.  
D200  
Adjust the level of the appliance by screwing out the  
adjustable foot, or feet, at the bottom of the cabinet  
using your fingers or a tool (see figure).  
A
Shelf holders  
Your appliance is equipped with shelf retainers that  
make it possible to secure the shelves during  
transportation.  
B
To remove them proceed as follows:  
Move the shelf retainers in the direction of the arrow,  
raise the shelf from the rear and push it forward until  
it is freed and remove the retainers.  
C
14  
 
The plug moulded onto the lead incorporates a fuse.  
For replacement, use a 13amp BSI362 fuse. Only  
ASTA or BSI approved fuses should be used.  
Electrical connections  
Any electrical work required to install this appliance  
should be carried out by a qualified electrician or  
competent person.  
The plug must not be used if the fuse cover/carrier is  
lost. The cover/carrier is indicated by the coloured  
insert at the base of the plug.  
WARNING:THIS APPLIANCE MUST BE  
EARTHED.  
A replacement cover/carrier must be obtained from  
your local Service Force Centre.  
The manufacturer declines any liability should  
this safety measure not be observed.  
This appliance complies with the E.E.C. Directive  
No. 87/308 of 2.6.87 relative to radio interference  
suppression.  
If the plug that is fitted to your appliance is not  
suitable for your socket outlet, it must be cut off and  
the appropriate plug fitted.  
This appliance complies with the following  
E.E.C. Directives:  
Remove the fuse from the cut off plug.  
-
-
73/23 EEC of 19.2.73 (Low Voltage Directive)  
and subsequent modifications;  
The cut off plug should then be disposed of to  
prevent the hazard of shocks in case it should be  
plugged into a 13amp socket in another part of your  
home.  
89/336 EEC of 3.5.89 (Electromagnetic  
Compatibility Directive) and subsequent  
modifications.  
Please ensure that when the appliance is  
installed it is easily accessible for the engineer in  
the event of a breakdown.  
Important  
The wires in the mains lead are coloured in  
accordance with the following code:  
Green andYellow  
Blue  
- Earth  
- Neutral  
- Live  
Brown  
If you fit your own plug, the colours of the wires in  
the mains lead of your appliance may not correspond  
with the markings identifying the terminals in your  
plug, proceed as follows:  
GREEN & YELLOW  
13 AMP. FUSE  
BROWN  
BLUE  
CORD CLAMP  
D207  
Connect the Green and Yellow (earth) wire to the  
terminal in the plug which is marked with the letter  
«E» or the earth symbol  
yellow.  
or coloured green and  
Connect the blue (neutral) wire to the terminal in the  
plug which is marked with the letter «N» or coloured  
black.  
Connect the brown (live) wire to the terminal in the  
plug which is marked with the letter «L» or coloured  
red.  
15  
 
Rear spacers  
In the bag with the documentation, there are two  
spacers which must be fitted as shown in the figure.  
Slacken the screws and insert the spacer under the  
screw head, then re-tighten the screws.  
D594  
Door reversal directions  
1. Disconnect from the electricity supply.  
E
E
2. Gently lay the fridge/freezer on its back with the  
top held away from the floor by 5-8 cm (2-3  
inches) of packing;  
F
F
3. Remove the ventilation grill (D).  
4. remove the bottom hinge (E) by unscrewing its  
fixing screws;  
D
F
5. Remove the freezer door by releasing it from the  
middle hinge (H).  
PR18  
6. Unscrew the middle hinge.  
7. Remove the fridge door by releasing it from the  
top hinge pin (G).  
H
8. Remove the pin then mount these on the side,  
after having removed the small plugs which  
should then be fitted on the opposite side.  
9. reassemble the door;  
10. using a 10 mm spanner, unscrew the hinge pin  
(E) and reassemble it on the opposite side of the  
hinge;  
11.Refit the fridge door and replace the middle hinge  
to the left hand side.  
12.reassemble the lower hinge (E) on the opposite  
side, using the screws previously removed. Slide  
the hole cover (F) out of the ventilation grille (D)  
by pushing it in the direction of the arrow and  
reassemble it on the opposite side;  
G
13.refit the ventilation grille (D), clipping it into place;  
The doors can be aligned by adjusting the middle  
hinge.  
The middle hinge can be adjusted horizontally, after  
having slackened the two screws with a screwdriver.  
Important  
After completion of the door reversing operation,  
check that the door gasket adheres to the cabinet. If  
the ambient temperature is cold (i.e. in Winter), the  
gasket may not fit perfectly to the cabinet. In that  
case, wait for the natural fitting of the gasket or  
accelerate this process by heating up the part  
involved with a normal hairdryer on a low setting.  
16  
 
 
 
 
© Electrolux plc 2004  
 

Weslo Treadmill WCTL26080 User Manual
Westinghouse Food Processor WST2025ZE User Manual
Whirlpool Stereo Amplifier PKT D1 User Manual
Williams Furnace 14036 User Manual
Woods Equipment Lawn Mower RD990X User Manual
Xantrex Technology Printer Accessories TFB110 User Manual
Yamaha Automobile Parts 14B 28199 11 User Manual
Zanussi Washer ZWH 5145 User Manual
Zanussi Washer ZWX 1506 W User Manual
Zebra Technologies Printer P310C User Manual